一、制作衣服架子
1、 Making clothes racks
為了后續步驟的順利實施，我們要先做一個衣服架子使得衣服能伸展平整便于后續制作步驟的實施
For the smooth implementation of the subsequent steps, we need to first make a clothes rack so that the clothes can be stretched and flattened for the implementation of the subsequent production steps
1.把衣服放在硬紙板上鋪平整，然后用記號筆在硬紙板上畫出衣服的大樣來。
1. Lay the clothes flat on cardboard, and then use a marker to draw a large sample of the clothes on the cardboard.
2.按照那也大樣來裁剪硬紙板。
2. Cut the cardboard according to the sample.
3.后修剪至合適大小塞入衣服內，使衣服顯得平整。
3. Trim to the appropriate size and insert into the clothes to make them appear flat.
二、制作衣服耐磨層紙樣
2、 Make a pattern for the wear-resistant layer of clothing
為了爬行時使得衣服比較耐磨，衣服上經常接觸地面的部分需要增加一層耐磨層，這樣也能隔絕地面上的濕氣傳入衣服內部，使得狙擊手趴在地上難受。
In order to make the clothes more wear-resistant when crawling, a wear-resistant layer needs to be added to the parts of the clothes that frequently come into contact with the ground, which can also isolate moisture from the ground from entering the interior of the clothes, making it difficult for snipers to lie on the ground.
1把裁紙樣的白卡紙放在衣服上，下方與衣角線齊平。
1. Place the cut pattern white cardboard on the clothes, with the bottom flush with the hem line.
2卡紙左邊邊界一紐扣眼為界（拉鏈式的以拉鏈的縫合線為界)
2. The left boundary of the cardboard is defined by a button eye (zipper style is defined by the stitching of the zipper)
3決定耐磨層上方的高度后，在卡紙上畫一道橫線。
After determining the height above the wear-resistant layer, draw a horizontal line on the cardboard.
4右方沿上衣外側鋒線畫上線條
Draw a line along the outer front line of the top on the right side
5把紙樣團剪出，在復制一塊，便成了一對后對稱的耐磨層紙樣。
Cut out 5 pieces of paper samples and replicate them to create a pair of symmetrical wear-resistant layer paper samples.
6右手扣扳機者，于右肩膀出一缺口，使得槍托可抵押著肩膀。（左撇子的話就把扣扳機的那側留此缺口）
The person who pulls the trigger with his right hand makes a gap in his right shoulder, allowing the butt of the gun to be secured against his shoulder. (If left handed, leave this gap on the side that pulls the trigger)
7耐磨層灰色部分大至與紙樣相同，只不過是沿內線像內縮5cm便可。
The gray part of the 7 wear-resistant layer is as large as the paper sample, but it can be shrunk 5cm along the inner line image.
三、縫合
3、 Suture
把做耐磨層的帆布按照紙樣裁剪完成后，就縫合在衣服的相應位置上（
山東三所新材料廠家認為，您如果手工不好的話就交給專門的人士去做吧）。
After cutting the canvas for the wear-resistant layer according to the paper pattern, it is sewn onto the corresponding position of the clothes (Shandong Three New Material Manufacturers believe that if your hand is not good, you can hand it over to a specialized person to do it).
1用雙面膠帶把耐磨層與填充物粘貼在一起（就是那個防潮墊），在放于相對位置，便可開始縫合操作。
1. Use double-sided tape to stick the wear-resistant layer and filling material together (that is, the moisture-proof pad), and place it in the opposite position to start the stitching operation.
2一些野戰服袖子上已經有耐磨補丁，這時便可把補丁上端的縫線拆去，把填充物塞進去，在縫合起來就完成了。
Some field uniforms already have wear-resistant patches on their sleeves. At this point, the stitching on the top of the patch can be removed, the filling material inserted, and the stitching is completed.
3完成品的大概樣子。
The approximate appearance of the completed product.
That's all for the production of camouflage suits for camouflage in the wild. If you have any doubts or needs, please come to our website http://www.jd-sj.com Consult and understand!
山東三所新材料技術有限公司
掃碼微信聯系
分類中心